Changing Default Boot in UBuntu with grub 2


Steps:
1. Open /boot/grub/grub.cfg to check boot items, in my case I want to select Window 7 as default boot.
Find for the line:

### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
set have_grubenv=true
load_env
fi
set default="Windows 7 (loader) (on /dev/sda2)"
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi

2. Copy "Windows 7 (loader) (on /dev/sda2)"
3. Open /etc/default/grub, find the line GRUB_DEFAULT=0 and change it to
GRUB_DEFAULT="Windows 7 (loader) (on /dev/sda2)"
4. Update/boot/grub/grub.cfg using sudo update-grub.
5. Reboot to check the changes.

If you are lazy,just install StartUp-Manager in Ubuntu software center or via apt-get

Comments

Post a Comment

Popular posts from this blog

Is Kuala Lumpur Water Hard or Soft? Is it safe to drink?

Image
What is the hardness level of Malaysia water source?  According to Wikipedia, water is classify as soft water when the hardness is below 60 mg/L, below 60 ppm or below 3.5gpg ( grain per gallon) .  ( Hard/ Soft Calssification Table, Source:  Wikipedia - Hard Water  ) * Parts per million (ppm) is usually defined as 1 mg/L CaCO3. It is equivalent to mg/L One recently study on Kuala Lumpur Tap Water in 2007 has shown that most populated areas in Kuala Lumpur are soft water. (source:  A Survey Of Tap Water Quality in Kuala Lumpur - March 2007  )  Also commentary of the study has confirmed that piece of finding. "As shown in figure 3, the hardness of tap water in these20 selected areas ranged from 48 mg CaCO3/L to 92 mgCaCO3/L with an average of 65 mg CaCO3/L. The tapwater in all these areas is considered soft as the hardnesslevel is below 100 mg CaCO3/L. Although there is nohealth-based guideline value, soft water and low pH maycause corrosion of pipes result
Read more

How to Reset Xiao Mi Power Bank

Image
According to Mi official website, Mi Power Bank 10400mAh 10400mAh should charge within 12 hours for a standard 1A charger. I have a 10400 Mi Power Bank but it take >24 hours to charge. I contacted Xiao Mi Support and indeed this is not normal. They suggested to Reboot the power bank. To do that: Press the Power Button for more than 15 secs.  After that drain the power bank and charge again. The power bank should fully charge about 12 hours or in some case 13 hours is fine.  The support person also suggested if the unit still behaves the same, we should bring it to the nearest service center for checking. http://www.mi.com/my/service/repair/
Read more

What need to be done after purchase a property in Malaysia

The process of purchase a house is not end at the moment we get the house key. We need to inform various authorities regarding the change of ownership. There are 5 of them. Cukai Taksiran/ Pintu Cukai Tanah ( Don't not get confuse with cukai taksiran)  Electricity - Tenaga Nasional Berhad Water Supply - Syabas Indah Water Konsortium It take me a lot of time to understand and research the whole process hence I'm writing down my own experience, hopefully this will help some of you out-there. The example below is specific to Selangor hence it will be different for other state. When in doubt, always call your Municipal Council for more information.  Tips: You will always need IC and S&P, make at least 4-5 copies of them.  Cukai Taksiran Cukai Taksiran need to be done at municipal council, aka local Majlis Perbandaran. In my case, I did it in MPSJ (Majlis Perbandaran Subang Jaya), which located in USJ 5, Subang Jaya ( click here for google maps ). To transfer t
Read more